● 化学薬品工業 ● 医薬品工業 ● 石油化学工業
● 電気化学工業 ● 油脂工業 食品酪農工業
醸造工業 ● 紙パルプ工業 合成ゴム工業
● 合成洗剤工業



上記の工業分野以外に、原子力装置、製鉄、熱交換器、温泉など多方面に活躍しています。
高度な技術と確かな信頼性で、皆様の幅広いニーズにお応えしています。
In addition to the industrial field listed on the above, our superior quality and technology serve your demanding needs in nuclear power equipment, steel making, heat exchangers, and hot spring resorts.


●外観・寸法検査
社内検査基準により実施します。特別な条件が必要な場合はご指示ください。
●高圧放電検査
ガラス面はDC15,000V(2.3mA)のピンホールテスターで検査します。
●Visual and dimension inspections
We perform these inspections in our company according to our own inspection criteria, but if you have special conditions, please specify them.
●High voltage discharge inspection
We inspect the glass surfaces with a DC 15,000V(2.3mA)pin hole tester.


●耐食性
フッ化水素、フッ酸、アルカリを除くほとんどの酸や溶剤に、すぐれた耐食性を発揮します。
●Corrosion resistance
Glassed steel pipe is highly resistant to corrosion by most acids and solvents, except for hydrogen
fluoride, fluoricacid, and alkalis.

●機械的強度
圧力強度
50Ax300lの直管2本、90°エルボ1本を配管した試料を用いて、水圧50kg/cm2
で5分間テストをおこない異常のないことを確認しておりますが、使用圧力は10kg/cm2以下とします。
●Mechanical strength
Pressure strength
In a pressure test using two 50-A, 300-1 straight pipes connected by a 90°elbow, the pipes were
confirmed to haveno abnormalities after being tested for five minutes at a water pressure of 50kg/cu,
though the normal use pressure does not exceed 10kg/cu

曲げ強度
試料50Aのガラス鋼管3,000lを5等分して支点距離400mmとし、アムスラー試験機で、
たわみ破壊強度を測定した結果、1,000kgまで亀裂が発生しませんでした。
Bending strength
A 50-A, 3000-l glassed steel pipe test piece divided up into five equal-length pieces 400mm long was
tested for its flexible rupture strength. The results of the test revealed fractures at 1000kg.

衝撃強度
コンクリート床上に厚さ40mmの鋼板1枚を敷き、試料(50A長さ100mmSGP+ガラスライニング)を水平に設置。重量285kg
の鋼球を垂直に自然落下させ、ガラスの剥離、クラックの有無をテストしましたが、500mmの高さまで異常はありません。
Shock strength
A test piece (50A x 100mm long SGP plus glass lining) laid on a 40mm-thick steel plate laid on a concrete
floor was tested for glass separation and cracking by dropping a 285g steel ball (42mm in diameter) on it,
but no abnormality wasdiscovered at drop heights up to 500mm.

●熱伝導性と総括伝熱係数
実際の使用では、管内の境膜電熱係数の数値によって変化するため一概にはいえませんが、
鋼管厚み2.8〜5.0mm、ガラス厚み0.5〜1.5mmで総括伝熱係数は180〜600kcal/m2・hr・℃となります。
●Thermal Conductivity and Overall Heat
Transfer Coefficient These characteristics will vary in actual use depending on the film heat transfer coefficient in the pipe, but generally speaking, the coefficient will be between 180 and 600kcal/uhr℃ in a pipe with a steel pipe wall thickness of 2.8 to 5.0mm and a glass wall thickness of 0.5 to 1.5mm

●耐熱性
使用温度
使用条件によって差がありますが、-10℃〜230℃の範囲です
●Thermal Resistance
Usable temperature range This range will vary depending on the use conditions, but it can generally besaid
to be -10℃ to 230℃.

瞬間温度差
表現方法によって差異はありますが、水での繰り返し熱衝撃テストの結果、温度差120℃まで安全です。
Momentary temperature difference
There will be differences depending on the way it is expressed, but in a repeated thermal shock test using
water, the pipe was shown to be safe at a temperature difference of 120℃.